Long Booster
New generation booster ! Completely VOC-free, even used pure during testing, it gives no positive result in VOC. With an effect for nearly three months, this booster is the fastest of his generation !

Use TEMPO LONG BOOSTER on the rubber only. Repeat the application every 24 hours for a better speed affect. After the last layer, let it dry until the rubber will become flat again. Join the rubber and the blade with water-based glue.
Efficient 8 to 12 weeks.

Packaged in 25ml and 150ml.

Booster
A VOC-free booster that gives the same feeling as speed glue for 4 weeks !

Use TEMPO BOOSTER on the rubber only. Repeat the application every 12 hours for a better speed affect. After the last layer, let it dry until the rubber will become flat again. Join the rubber and the blade with water-based glue.
Efficient 2 to 4 weeks.

Packaged in 25ml and 150ml.

Life Expander
Feeds – Protects – Prolongs – Unglues

It feeds your rubber, keeps the rubber elastic longer. Prolongs the life of speed glue integrated rubbers by 3 fold. Reduces risk of cracking and bubbles. Restores the grip ! VOC free.

For any rubbers:
Apply a single layer on the topsheet side between 2 and 4 times a month. Let it penetrate for a few minutes.

For speed glue integrated rubbers :
On the topsheet side, apply a layer between 2 and 4 times a month and on the sponge side, apply a layer once or twice a month. Let it penetrate on the sponge for a few hours.

Unglue :
Apply a small amount between Falco Water Sheet II and the rubber to help take them off.

Do not apply the FALCO LIFE EXPANDER more than the indicated frequency because the rubber could become engorged. If used correctly, the container should be enough to feed and protect 6 rubbers for 6 months.

Packaged in 25ml and 100ml.

Water Glue 10'
Your water-based glue damages your rubbers and your blade when you take off ? Your water-based glue is slow to dry ? Use the Water Glue 10' ! Water-based and natural rubber glue. Easy to take off while maintaining good adhesion between the rubber and the blade !

Put the glue on the rubber and the blade. Let it dry 10'. Assemble the rubber and the blade. Put 2 layers for new rubbers.
Affected by frost.

Packaged in 100ml and 500ml.

Water Sheet II
Your PSA sheet damages your equipment and leaves a residue ? Here is the response of Falco : Falco Water Sheet II, glues in 30 seconds without damaging the blade or the sponge, VOC-free adhesive solution without residue! Use Falco Life Expander to assist take-off !

Take off the first protection sheet (the white one)
Apply the sheet on the blade and press it
Take off the second protection sheet (the brown one)
Cut the sheet around the blade
Join the rubber and press strongly
Cut your rubber

Normal glue with VOC
Solvent-based glue, allows a very good traction between the rubber and the blade without damaging them during takeoff !

Put the glue on the rubber and the blade. Let it dry 5'. Assemble the rubber and the blade. Put 2 layers for new rubbers. After complete drying, most VOCs are evaporated. Proceed to gluing your racket a few days earlier and leave it in the open air and this to be sure to pass "Anti VOC" tests.

Packaged in 250ml, 1L and 5L.

Speed Glue with VOC
Solvent-based glue increases the speed of your rubbers ! This adhesive doesn't damage your rubbers and your blade because it was designed to take off and stick them several times at short intervals.

Put the glue on the rubber and the blade. Let it dry 5'. Assemble the rubber and the blade. Put 2 layers for new rubbers. For competitions, prefer the normal glue with VOC, because you have to leave the racket in the open air at least 48 hours for VOCs are evaporated. If you use speed glue, the entire effect of the product will be lost during this period. For having the best record, play once the racket stuck.

Packaged in 250ml, 1L and 5L.